气瓶内部淬火过程的流动换热特性

 大直径厚壁气瓶内部淬火时的流动换热过程极其复杂，受到多种因素的影响，而研究气瓶内部压强和温度的变化规律对改善流动换热效果、提高产品组织性能具有重要的理论指导意义。以914 mm厚壁气瓶和瓶内流体为研究对象，建立了二维等效流 固耦合模型；采用多喷嘴系统对气瓶内外进行喷水淬火，研究了气瓶总长、喷水流速及淬火时间对瓶内压强及内壁温度的影响，通过间歇淬火试验验证了数学模型的正确性。结果发现，气瓶长度对瓶内压强和瓶壁温度的影响显著，喷水流速次之，当喷水流速大于8 m/s后，水量对瓶壁的冷却效果大大降低；气瓶内壁长度方向的温度梯度分别随气瓶总长的增加和淬火时间的延长而减小，但基本不受喷水量的影响。     

某矿快速掘进最优炮孔间距的选择

山西某矿5308底抽巷在掘进过程中速度慢、效率低，直接影响工作面的瓦斯抽采，为了改善上述情形，对炮孔间距进行研究。通过使用ANSYS软件对不同炮孔间距下快速掘进效果的模拟分析，并经现场验证，得出了适应该矿的最佳炮孔间距。结果表明：炮孔间距为500 mm时，爆破产生裂隙发育范围和岩石损伤区域都最大，快速掘进的效果最好。     

Interfacial Crystallization of Diacylglycerols Rich in Medium‐ and Long‐Chain Fatty Acids in Water‐in‐Oil Emulsions

The effects of diacylglycerols rich in medium‐ and long‐chain fatty acids (MLCD) on the crystallization of hydrogenated palm oil (HPO) and formation of 10% water‐in‐oil (W/O) emulsion are studied, and compared with the common surfactants monostearoylglycerol (MSG) and polyglycerol polyricinoleate (PGPR). Polarized light microscopy reveals that emulsions made with MLCD form crystals around dispersed water droplets and promotes HPO crystallization at the oil‐water interface. Similar behavior is also observed in MSG‐stabilized emulsions, but is absent from emulsions made with PGPR. The large deformation yield value of the test W/O emulsion is increased four‐fold versus those stabilized via PGPR due to interfacial crystallization of HPO. However, there are no large differences in droplet size, solid fat content (SFC), thermal behavior or polymorphism to account for these substantial changes, implying that the spatial distribution of the HPO crystals within the crystal network is the driving factor responsible for the observed textural differences. MLCD‐covered water droplets act as active fillers and interact with surrounding fat crystals to enhance the rigidity of emulsion. This study provides new insights regarding the use of MLCD in W/O emulsions as template for interfacial crystallization and the possibility of tailoring their large deformation behavior. Practical Applications: MLCD is applied in preparing W/O emulsion. It is found that MLCD forms unique interfacial Pickering crystals around water droplets, which promote the surface‐inactive HPO nucleation at the oil‐water interface. Thus MLCD‐covered water droplets act as active fillers and interact with surrounding fat crystals, which can greatly enhance the rigidity of emulsion. This observation would provide a theoretical reference and practical basis for the application of the MLCD with appreciable nutritional properties in lipid‐rich products such as whipped cream, shortenings margarine, butter and ice cream, so as to substitute hydrogenated oil. MLCD‐stabilized emulsions can also be explored for the development of novel confectionery products, lipsticks, or controlled release matrices.     

Association of solid fuel use with risk of stunting in children living in China

Stunting adversely affects physical and mental outcomes of children. It has not been examined whether household air pollution from solid fuel combustion is a risk factor for stunting in children. In a total of 41,439 children aged 6-17 across China, height was measured using a unified protocol. Multivariable linear regression models and logistic regression models were used to assess the associations of solid fuel use for cooking/heating with stunting in children. Adjusted for covariates, cooking/heating with solid fuel was significantly associated with a lower z-score for height for age and sex (β = −0.21 [−0.32 to −0.09] and −0.17 [−0.31 to −0.03], respectively) and an increased risk of stunting with an estimated ORs of 1.34 [1.07~1.68] and 1.37 [1.02~1.83], respectively. The risk of stunting associated with solid fuel use was statistically significant in high-age children. And the effect was greater on girls than on boys, though the difference was not statistically significant. Our study suggested that Chinese children living in households using solid fuel had a significantly higher risk of stunting than those living in households using cleaner fuel.     

基于Matlab的制芯机器人夹持器稳定性研究与分析

由于铸造厂制芯机器人的工作环境恶劣,机器人抓取砂芯的稳定性较差,时常出现掉砂芯、夹伤砂芯的问题。针对上述问题建立以夹持器、气压、机械振动的系统数学模型,采用高阶系统极点在[s]平面的分布法来判定该系统的稳定性。在确保高阶系统极点值不变的情况下,通过改变系统的零点值来观察零点值对系统稳定性、振荡衰减时间的影响。用Matlab的pzmap和impulse函数分别对系统的零点、极点分布和零点值的不同对系统响应进行仿真,运用仿真结果与现场试验进行优化参数,结果表明采用一种刚度与柔度各为1/2的夹持器对制芯机器人的稳定性具有较好优化效果。     

A web-based software tool for participatory optimization of conservation practices in watersheds

WRESTORE (Watershed Restoration Using Spatio-Temporal Optimization of Resources) is a web-based, participatory planning tool that can be used to engage with watershed stakeholder communities, and involve them in using science-based, human-guided, interactive simulation–optimization methods for designing potential conservation practices on their landscape. The underlying optimization algorithms, process simulation models, and interfaces allow users to not only spatially optimize the locations and types of new conservation practices based on quantifiable goals estimated by the dynamic simulation models, but also to include their personal subjective and/or unquantifiable criteria in the location and design of these practices. In this paper, we describe the software, interfaces, and architecture of WRESTORE, provide scenarios for implementing the WRESTORE tool in a watershed community's planning process, and discuss considerations for future developments.     

Symptoms and risks for musculoskeletal disorders among male and female footwear industry workers

BackgroundConsidering the growing participation of woman in the labor market and the high prevalence of the musculoskeletal disorders (MSD) in the footwear industry workers, the aim of this study was to evaluate and compare female and male footwear industry workers in relation to their demographics, occupational characteristics, stress levels, MSD symptoms prevalence, physical activity levels, alcohol and tobacco use.MethodsThe study included 175 female and 182 male footwear industry workers. Data was collected using the Perceived Stress Scale – 10, the Standardized Nordic Questionnaire, the International Physical Activity Questionnaire, the Alcohol Use Disorders Identification Test, and the Fagerstrom test for Nicotine Dependence.ResultsThe female workers were younger, had less time in the company and in the current job. They reported more stress (p = 0.001), had less time for physical activity (p = 0.004), higher prevalence of MSD symptoms in the last 12 months (p = 0.003), and consumed less alcohol (p = 0.006) than the male workers.ConclusionsFemale and male footwear industry workers presented significant differences in their demographics, occupational characteristics, stress levels, MSD prevalence, physical activity levels, alcohol and tobacco use. These differences should be taken into consideration in the implementation of intervention programs for optimum outcomes.Relevance to industryFemale footwear industry workers were more stressed, presented higher prevalence of MSD symptoms, and reported less time for physical activity than male footwear industry workers. The differences between male and female workers should be taken into consideration in the implementation of MSD prevention programs.     

Deep Integration of Innovation and Entrepreneurship (InE) Education in Chinese University Classrooms

Recently, InE has been regarded as a popular education strategy in Chinese universities. However, problems have been exposed in the adoption of InE, for example, in InE courses and competitions. The purpose of this paper is to provide a possible solution to the problems, which is to organize effective InE courses by integrating InE with Inter-Course-level Problem-Based Learning (ICPBL). A detailed case is demonstrated by an ICPBL elective course design with deep integration of InE in the teaching, learning, and assessments. This paper contributes to a new curriculum design for promoting InE education in practically for Chinese universities.     

煤磨热风管道改造的效果

中联万基水泥有限公司4500t/d熟料生产线采用SCLW4-12×13.4第四代篦冷机,煤磨热风取风口和余热发电AQC热风取风口在篦冷机同一对称位置,煤磨与余热发电系统存在争风现象,开停煤磨对余热发电系统影响较大。通过从废气管道处开孔,加装管道和电动阀,与热风管道汇合通往煤磨沉降室,调整相应阀门开度,可以控制入煤磨烟气温度,这样不但提高了余热发电量,而且提高了煤磨产量,同时也降低了窑头排风机的负荷,降低了熟料生产电耗。